HARMAN KARDON AVR435
Manual de Usuario

ADVANCED FEATURES
Press the Set Button q to enter the ADVANCED SELECT menu. When the ADVANCED SELECT menu appears, press the �/¤ Navigation Button o so that the cursor is pointing to the SEMI OSD/TIME OUT line. Select one of these options: � To keep the semi-OSD system activated, but to adjust the length of time the displays remain on the screen, press the � / � Navigation Button o until the desired time-out is shown. The default setting is 5 seconds. � To turn the semi-OSD system off so that it does not appear at any time, press the � / � Navigation Button o so that OFF is shown on the right side of the line. If you wish to make other adjustments, press the �/¤ Navigation Button o until the cursor is next to the desired setting or the BACK TO MASTER MENU line and press the Set Button q. If you have no other adjustments to make, press the OSD Button U to exit the menu system. Full-OSD Time-Out Adjustment The FULL OSD menu system is used to simplify the setup and adjustment of the AVR 435 by using a series of on-screen menus. The factory default setting for these menus leaves them on the screen for 20 seconds after a period of inactivity before they disappear from the screen (Time-Out). Time-Out is a safety measure to prevent image retention of the menu text in your monitor or projector, which might happen if it were left on indefinitely. However, some viewers may prefer a slightly longer or shorter period before the on-screen display disappears. To change the full-OSD Time-Out, you will need to make an adjustment in the ADVANCED SELECT menu (Figure 17). To start the adjustment, press the OSD Button U to bring the MASTER MENU to the screen. Press the ¤ Navigation Button o, until the on-screen   cursor is next to the ADVANCED line. Press the Set Button q to enter the ADVANCED SELECT menu (Figure 22). At the ADVANCED SELECT menu (Fig. 22) make certain that the cursor is next to the FULL OSD TIME OUT line by pressing the �/¤ Navigation Button o as needed. Next, press the � / � Navigation Button o until the desired time is displayed in seconds. Unlike most of the other options in this menu, this is a permanent setting change, and the Time-Out entry will remain in effect until it is changed, even if the unit is turned off. If you wish to make other adjustments, press the �/¤ Navigation Button o until the cursor is next to the desired setting or the BACK TO MASTER MENU line and press the Set Button q. If you have no other adjustments to make, press the OSD Button U to exit the menu system. Digital Auto-Poll Settings In order to provide the greatest flexibility in accommodating the widest range of sources, the AVR 435 includes both analog and digital audio inputs for all sources. In most cases you will want to use one or the other, but not both. However, in some circumstances it is desirable to make both an analog and digital connection between a source device and the AVR. An important application for dual audio connections is with cable or satellite boxes, where the audio output may change depending on the channel being viewed and the type of audio the cable system or satellite receiver associates with it. To eliminate the need to constantly switch back and for to select an audio type each time you change channels, the AVR 435 is programmed by default to automatically �poll� the audio inputs. When a digital audio stream it is selected first, but if the digital audio is removed the AVR will switch to the analog inputs associated with that input as a back-up. In most systems this is the correct operation and no further change is required. However, if this configuration does not suit your system application the AVR 435 gives you the flexibility to turn the digital audio auto polling on or off on an input-by-input basis. When the Auto Polling is set to OFF, the system will keep the digital audio input active and not attempt to switch to the analog source even when the digital data stream stops. If you wish to change the auto poll setting, first select the input you wish to configure by pressing the appropriate Input Selector dD on the remote, or on the SOURCE line pf the IN/OUT SETUP menu (Figure 2). Next, with the ADVANCED SELECT MENU (Figure 22) on the screen, press the � / � Navigation Button o so that the cursor is pointing to the AUTO POLL line. Press the � / � Navigation Button o to change a default setting so that OFF is shown in highlighted video or to ON so that the original setting is restored and the auto polling is once again activated. Since this setting is unique to each input, you must return to the INPUT SETUP menu to change any other inputs. To do that, press the � / � Navigation Button o so that the cursor is pointing to the BACK TO MASTER MENU line and press the Set Button q. At the MASTER MENU (Figure 1), press the � / � Navigation Button o so that the cursor is pointing to the IN/OUT SETUP line. Press the Set Button q and then follow the instructions shown on page xx to change the input source. Return to the ADVANCED MENU to reconfigure the auto poll setting for the newly selected input. When all changes to the Auto Poll settings have been made, press the � / � Navigation Button o to select another configuration option on the ADVANCED SETUP Menu, move the cursor to BACK TO MASTER MENU line and press the Set Button q to make a change to another menu option, or simply press the OSD Button U to exit the menu system.

40

ADVANCED FEATURES